Ruger Forum banner

Reaction score
82

Marketplace Rating
(0.0 - 0 reviews)

Profile posts Latest activity Discussions Buy & Sell Reviews About

  • · Registered
    Joined
    ·
    10,153 Posts
    Har har kinda hard to scope a Rossi Model 92 & no to a scout scope my gun barrel wasn't tapped. No to peep sights. This gun is my recreational shooter. I want a scoped rifle wether it's lever or bolt for more precise shooting

    · Registered
    Joined
    ·
    734 Posts
    You need an M1 Garand. Everyone needs an M1 Garand. I bought one for my Da, and it cost less (including my membership in the Garand Collector Assoc.) than the GP100 that I bought from Gander Mtn. When it showed up at my door (no FFL needed where I live if you buy from the CMP) it was absolutely pristine. CMP Sales

    · Registered
    Joined
    ·
    10,153 Posts
    All I can say is I was talking about that my Rossi Model 92 is just going to be a plinking gun with open sights

    · Registered
    Joined
    ·
    499 Posts
    Hey, thanks for the welcome
    My Wife and I have lived here for 7 years now
    Great little town
    Where are you living now ?

    · Registered
    Joined
    ·
    10,153 Posts
    Ok I will figure shipping weight 1pound & call the post office tomorrow for your zip code so the cost of the scope + shipping

    · Registered
    Joined
    ·
    10,153 Posts
    Ok if I am doing this correctly not the regular type of message I am use to how much do you want for the cylinder. I might have to have the cylinder fitted to my gun.

    · Registered
    Joined
    ·
    10,153 Posts
    Your cylinder is it from a BlackHawk? I was told a cylinder like yours would fit my Ruger Vaquero. My gun is the older Vaquero larger frame. How much do you want for it? I might have to get your cylinder fitted to my frame by Ruger to work

    · Registered
    Joined
    ·
    26 Posts
    Just looked under the house, the cylinder is a 9mm. The case mouth rests on a ledge, 0.7" into the cylinder. 202 is etched into the top face of the cylinder, along with what could be a "9" or a "D" on the bottom. There is an "S" stamped into the rear of the cylinder. The ratchets look good, I don't think there's been a lot of use, not discolored or etched. The felt bag is still serviceable.

    What's your proposal?

    Thanks,
    Bruce


    [IMG]
    [IMG]
    [IMG]

    · Registered
    Joined
    ·
    10,153 Posts
    Monty B
    I am still looking for a composite stock for my Mini 14. My gun has the Original factory Birch Stock. My gun is about a 2003-2005 with the thin profile barrel. So right now yes I am still looking.

    · Registered
    Joined
    ·
    129 Posts
    i see you are looking for a composite stock for your mini-14. is that to say you have the stock you are replacing?

    · Registered
    Joined
    ·
    9 Posts
    Well, look around and make sure that ammo is available for it in your area. I had to go on line to get 500rds for range work, but personal defense ammo is available here although it's a bit pricey..........ed

    · Registered
    Joined
    ·
    9 Posts
    Well, thanks for asking, but the .327 is off the market, there wasn't a lot of interest in it. So, at the Ft.Worth gun show I bought a gun belt and a Galco holster for it. Then I dropped it of at the XS Sight place and they are going to try one of their off the shelf sights on it and see how it shoots. Looks like I'm going to keep it a little longer....cheers, Ed

    · Registered
    Joined
    ·
    10,153 Posts
    Thanks its great to be here I especially like the fact there are areas to post for all types of Ruger Firearms!!
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Top