Ruger Forum

Ruger Single Action Trigger Job "step by step" video (Single Six)

This is a discussion on Ruger Single Action Trigger Job "step by step" video (Single Six) within the Ruger Single Action forums, part of the Pistol & Revolver Forum category; I made a 25 minute step by step process on how to do a trigger job on all your single action revolvers. I replaced the ...


Go Back   Ruger Forum > Pistol & Revolver Forum > Ruger Single Action

Reply
 
LinkBack Thread Tools Display Modes

Old November 22nd, 2012, 08:25 PM   #1
 
DIYautotech's Avatar
 
Join Date: Jan 2012
Location: Lake Forest, California
Posts: 144
DIYautotech is on a distinguished road
Ruger Single Action Trigger Job "step by step" video (Single Six)

I made a 25 minute step by step process on how to do a trigger job on all your single action revolvers. I replaced the trigger return spring. A video on how to replace the hammer main spring will be up next.
This was performed on a new model Ruger Single Six, but can be performed on all Ruger single action firearms, except the bearcat.

The instructions will be typically the same for each gun, the vaquero may vary slightly in screw placement and possible allen wrench.

Here's the link:



DIYautotech is offline  
Advertisements
Old November 22nd, 2012, 08:34 PM   #2
 
Join Date: Jul 2012
Location: Jacksonville, NC
Posts: 74
Country is on a distinguished road
Thanks for posting. Subscribed to watch later. And maybe attempt a trigger job.
Country is offline  
Old November 23rd, 2012, 11:06 AM   #3
 
Smithy's Avatar
 
Join Date: Jun 2011
Location: Central Valley of California
Posts: 1,217
Smithy is on a distinguished road
Great video. Thanks for posting. For your next production......
Quote:
A video on how to replace the hammer main spring will be up next.
you might consider the following part from Brownells.

MAINSPRING COMPRESSOR | Brownells

I too have done many an action job on several different guns, Rugers especially and this tool has saved many a fowl word after launching a spring to the far reaches of my garage. It can be clamped into a vise or it has a tab on it to push against the edge of one's bench top (the way I do it) and it make an otherwise tough job to a simple spring swap. Smithy.

Last edited by Smithy; November 23rd, 2012 at 08:35 PM.
Smithy is offline  
Old November 23rd, 2012, 11:31 AM   #4
 
OH25shooter's Avatar
 
Join Date: Jan 2012
Location: OH
Posts: 430
OH25shooter is on a distinguished road
Thumbs up

A tad long, but for an old guy like myself who doesn't read and sometimes understand directions, I liked the video. Good job.
OH25shooter is offline  
Reply

  Ruger Forum > Pistol & Revolver Forum > Ruger Single Action



Search tags for this page
action job on ruger vaquero
,
ruger blackhawk action job
,

ruger blackhawk trigger job

,
ruger blackhawk trigger job video
,

ruger single action trigger job

,

ruger single six trigger job

,
ruger single six trigger job instructions
,
ruger vaquero action job
,

ruger vaquero trigger job

,
single action trigger job
,
trigger job ruger vaquero
,
video on how to change main spring on blawkhawk
Click on a term to search for related topics.

Thread Tools
Display Modes


Similar Ruger Forum Discussions
Thread Thread Starter Forum Replies Last Post
"Left-handed" single action revolvers bearcatter Pistols & Revolvers 11 November 9th, 2011 04:37 PM
1 step forward, 2 steps back - SP101 trigger reset argyle Gunsmithing 6 May 23rd, 2009 12:59 PM
Single Six "Poor Boys" Trigger Job techase Ruger Single Action 7 February 11th, 2009 05:11 PM

Top Gun Sites Top Sites List  
Powered by vBulletin 3.8.7
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.1
Copyright © 2006 - 2014 Ruger Forum. All rights reserved.
Ruger Forum is a Ruger Firearms enthusiast's forum, but it is in no way affiliated with, nor does it represent Sturm Ruger & Company Inc. of Southport, CT.