f> New sear - Page 2 - Ruger Forum

Ruger Forum

New sear

This is a discussion on New sear within the Ruger Rimfires forums, part of the Pistol & Revolver Forum category; Originally Posted by stevenstark711 Will the volquartsen hammer bushing for the Mark 2 eork in a 22/45 Sent from my SM-G925P using Tapatalk Yes the ...


Go Back   Ruger Forum > Pistol & Revolver Forum > Ruger Rimfires

Reply
 
LinkBack Thread Tools Display Modes

Old March 26th, 2017, 03:54 PM   #16
 
Strawdog's Avatar
 
Join Date: Jul 2016
Location: Seacoast NH
Posts: 39
Strawdog is on a distinguished road
Quote:
Originally Posted by stevenstark711 View Post
Will the volquartsen hammer bushing for the Mark 2 eork in a 22/45

Sent from my SM-G925P using Tapatalk
Yes the Mkll hammer bushing does work in the 22/45. That along with the target sear from VQ will give you the most for your buck toward an awesome trigger pull.



Strawdog is offline  
Advertisements
Old March 26th, 2017, 03:59 PM   #17
 
stevenstark711's Avatar
 
Join Date: Mar 2015
Location: Muncie, IN
Posts: 34
stevenstark711 is on a distinguished road
No goi g bsck now

Sent from my SM-G925P using Tapatalk
stevenstark711 is offline  
Old March 26th, 2017, 04:01 PM   #18
 
stevenstark711's Avatar
 
Join Date: Mar 2015
Location: Muncie, IN
Posts: 34
stevenstark711 is on a distinguished road
Quote:
Originally Posted by stevenstark711 View Post
No going back now

Sent from my SM-G925P using Tapatalk


Sent from my SM-G925P using Tapatalk
stevenstark711 is offline  
 
Old March 31st, 2017, 06:27 AM   #19
 
Join Date: Feb 2017
Location: Delphos,Ohio
Posts: 8
satch is on a distinguished road
New Sear

Installed the Kit yesterday minus the trigger and the trigger break is crisp with only a little over 1/8 inch take up. Viewing the YouTube video was helpful but there was plenty of things to frustrate you. The bolt stop didn't just drop off and I spent 15 mins, prying it off with out trying to bending it, and it was almost as hard getting it back on. The sear install was easy, then came the Hammer. Three hands weren't enough putting that in and hooking up the safety at the same time. A tip here is to get the safety handle shaft through the Hammer to the right side and through, back it back a bit until the detent and spring can be added and then push it into the safety keyhole otherwise you'll go nuts trying to do both at the same time. But not a bad job for guy over 77, if I could you can.
satch is offline  
Old April 1st, 2017, 09:59 AM   #20
 
Join Date: Aug 2012
Location: Toledo
Posts: 186
dingode is on a distinguished road
I got my new sear installed in my MKIII 22/45 the other day too. I had problems keeping the dumb safety lever in place till I could get the pin in. All in all, it wasn't too bad, think it took me 30 minutes or so. Shot it today and it works great!
dingode is offline  
Reply

  Ruger Forum > Pistol & Revolver Forum > Ruger Rimfires

Thread Tools
Display Modes


Similar Ruger Forum Discussions
Thread Thread Starter Forum Replies Last Post
MIM sear spiker44 Ruger 10/22 Rimfire 12 March 17th, 2014 04:40 PM
77-22-VMBZ Sear morgan5430 Gunsmithing 0 November 3rd, 2013 09:29 AM
VQ Sear Gunny B Ruger Rimfires 6 August 25th, 2012 06:18 AM
Is it the Sear Spring? cbxbikenut Ruger Rimfires 8 July 7th, 2011 06:48 PM
New sear pin for 22/45's Bullseye Ruger Rimfires 9 July 23rd, 2007 04:49 PM

Top Gun Sites Top Sites List
Powered by vBulletin 3.8.7
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.1
Copyright © 2006 - 2017 Ruger Forum. All rights reserved.
Ruger Forum is a Ruger Firearms enthusiast's forum, but it is in no way affiliated with, nor does it represent Sturm Ruger & Company Inc. of Southport, CT.