SR9c slide release question ??

Bagger · 02-03-2010, 04:45 PM

I have a SR9 that is a not my primary gun ... that is a clone, the S/W M&P 9 mm in standard sized. But, the SR9 is my bedroom night table gun with a laser sight on it. I've had no problems with the SR9 to date. And, it is a fun gun to shoot.

I did buy a black SR9c this weekend. ($390) I have not shot the gun, but it is a fine piece in my opinion for daily carry. I usually carry either a LCP or Firestorm 380 depending on the weather, clothing and such.

The SR9c feels good in my hand and I like it. I do wonder why the slide release will not work with just my thumb. I have to move the slide back a smidge and then it releases. This is a PITA.

I wonder if anyone else has this problem. The S/Ws did not do so. And, I wonder if I run a few hundred rounds thru the SR9c if this problem will be 'fixed'.

Opinions? Recommendations? All will be well received. Thanx in advance.

PeteCamp · 02-03-2010, 08:13 PM

The reason it will not work like a slide release is because it is not one. It is a slide hold open. The instruction manual makes that clear.

Melissa5 · 02-03-2010, 08:36 PM

I've read a couple of range reports on other forums and they also mention that the slide release is very tight.

I'll be picking mine up tomorrow and will go right to the range with it. Can't wait.

theotherTexasRich · 02-03-2010, 09:43 PM

Bagger, I'd avoid using the slide stop to release the slide anyway. Over time it will wear out and it won't even hold the slide open. At that point, releasing the slide will no longer be a problem.

I prefer to release the slide myself, so I'm fine with the way the SR9 works.

Bagger · 02-04-2010, 05:53 AM

Thanx for the responses.

I have not read the manual as I figured it was much like the 'original SR9', but I will certainly read it. However, I have stripped the gun, cleaned it and oiled it ... but, I have not fired it.

I'm not sure why the 'slide stop lever' is soooooooo tight. I'm not a weak guy, I'm over 215 pounds and work out regularly. So, strength is not a problem. But, displacing the stop lever and pulling back on the slide takes considerable effort on my gun. My associate at work could not do it, nor could my girl friend.

BTW, this would not be good in a gun fight. Dropping the spent magazine, popping in a loaded mag and then wrestling with the slide stop lever to release the slide. I'm not sure I like this design.

I'm used to tossing in a fresh mag, dropping the slide stop lever and bang, bang. It takes less than 2 seconds with my M&P 9.

I do hope this improves.

Bagger · 02-04-2010, 09:09 AM

I just got off the phone with tech at Ruger in AZ. I spoke about the 'slide release lever' issue I have and as suspected, it is something that will improve.

Julian at Ruger said the parts are "square when machined" and that the lever will 'round off' with use. Also, the spring in the magazine is very stiff when new and once the gun is loaded (and kept loaded) the spring will relax allowing everything to move more fluidly. The lever should work well with the thumb 'once broken in'.

wrv · 02-04-2010, 09:32 AM

an interesting article about the debate can be found here:

http://www.officer.com/web/online/On-the-Street/The-Great-Slide-Release-Debate/21$36789

in my area, it is pretty common among LEO's to be trained with the slingshot method.

A4Guy · 02-08-2010, 08:37 PM

Mine is also very stiff. I don't mind it though. I just use the slingshot method. It only takes a tiny little tug back on the slide and the Slide Stop disengages. I don't have to pull back and then thumb the lever or anyhting. Just a tiny tug and let it go.

theotherTexasRich · 02-08-2010, 09:16 PM

Quote:

BTW, this would not be good in a gun fight. Dropping the spent magazine, popping in a loaded mag and then wrestling with the slide stop lever to release the slide. I'm not sure I like this design....

This is really a whole separate debate, but in all likelihood you will not have to reload during a self-defense shooting. 10 rounds is lots. Police face different circumstances than we do. I often carry a 5-round SP101 with no reload, and I feel comfortable. Will it be enough? I hope so! You must, of course, decide for yourself what is best for you, and I pass no judgment either way.

Quote:

...I'm used to tossing in a fresh mag, dropping the slide stop lever and bang, bang. It takes less than 2 seconds with my M&P 9.

The M&P is a wonderfully designed gun. Better than the SR9, IMO. But I am a Ruger guy, and, so far, all my handguns are Rugers. You should choose the gun you are most comfortable with, and train with that.

There is also a combat reload in which the magazine is swapped before the slide locks back. This could work for you as long as you train for it.

Bagger · 02-09-2010, 06:47 AM

TexasRich .... I fully understand and appreciate what you write. My training is different than what you describe. I have also dropped a magazine with a round or so still on board and rammed in a fresh mag while continuing to fire, too. However, most of these guns hold more than the SR9s 10 rounds and I feel more comfortable doing so.

From what I can see on other message boards and this one, the SR9c is designed to have the slide stop lever used for just that purpose and not a slide release lever. I don't know why, but that seems to be the facts.

I have 3 other Ruger pistols that seem to have the slide release lever work as such ... and not as a slide stop lever. This is what I am used to using.

I'm going to sell the SR9c. It's a fine gun, but I can't live with the slide stop lever working the way it does.

A4Guy · 02-09-2010, 07:24 AM

How much you want for your SR9c, Bagger?

Bagger · 02-09-2010, 07:33 AM

I was going to post this on the classified section .... which I prolly will anyway.

Here's the deal:

SR9c for sale in Connecticut.

Purchased1/30/10 new. Gun is black (not SS slide).

I have only run 250 rounds of 115 grn ammo from the LGS's indoor range a couple days ago. That is it.

Gun is in perfect condition as from the Ruger factory. All materials included from Ruger are in the box. Gun is cleaned, oiled and in original condition packaging.

I have photos if you are interested in seeing the gun.

Price: $300 plus over night shipping costs to a FFL only. This could be over $60 from what I can see.

Gun can not be shipped to CA, HI, MA, NJ, or NY because of extended magazine capacity. But, you already know this.

jman · 02-13-2010, 05:05 AM

Ok i bought my sr9c back in january and have shot 400 rounds and the slide is still tight. i have been reading up on the slide and am getting different opinions on why its so thight. some say its because the sr9c is new and needs to be broken in others say the gun is made this way and will stay this way? which one is it? does any one have a true answer?

areyna · 02-13-2010, 04:42 PM

jman - silly question, but have you cleaned all the factory lube out of it yet? My slide was tight as hell till i cleaned it. 150 rounds later and the slide and slide lock/release action is very similar to my SR9 (2k+ rounds).

02-03-2010, 04:45 PM	#1
Bagger Joined: Oct 2008 From: Southern New England Posts: 90	SR9c slide release question ?? I have a SR9 that is a not my primary gun ... that is a clone, the S/W M&P 9 mm in standard sized. But, the SR9 is my bedroom night table gun with a laser sight on it. I've had no problems with the SR9 to date. And, it is a fun gun to shoot. I did buy a black SR9c this weekend. ($390) I have not shot the gun, but it is a fine piece in my opinion for daily carry. I usually carry either a LCP or Firestorm 380 depending on the weather, clothing and such. The SR9c feels good in my hand and I like it. I do wonder why the slide release will not work with just my thumb. I have to move the slide back a smidge and then it releases. This is a PITA. I wonder if anyone else has this problem. The S/Ws did not do so. And, I wonder if I run a few hundred rounds thru the SR9c if this problem will be 'fixed'. Opinions? Recommendations? All will be well received. Thanx in advance.

02-04-2010, 09:09 AM	#6
Bagger Joined: Oct 2008 From: Southern New England Posts: 90	Spoke to Ruger in AZ ... I just got off the phone with tech at Ruger in AZ. I spoke about the 'slide release lever' issue I have and as suspected, it is something that will improve. Julian at Ruger said the parts are "square when machined" and that the lever will 'round off' with use. Also, the spring in the magazine is very stiff when new and once the gun is loaded (and kept loaded) the spring will relax allowing everything to move more fluidly. The lever should work well with the thumb 'once broken in'.

02-13-2010, 05:05 AM	#13
jman Joined: Feb 2010 From: Texas Posts: 1	slide Ok i bought my sr9c back in january and have shot 400 rounds and the slide is still tight. i have been reading up on the slide and am getting different opinions on why its so thight. some say its because the sr9c is new and needs to be broken in others say the gun is made this way and will stay this way? which one is it? does any one have a true answer?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-03-2010, 08:13 PM	#2
PeteCamp Joined: Jan 2010 From: Texas Posts: 2	The reason it will not work like a slide release is because it is not one. It is a slide hold open. The instruction manual makes that clear.

02-03-2010, 08:36 PM	#3
Melissa5 Joined: Sep 2009 From: Georgia Posts: 106	I've read a couple of range reports on other forums and they also mention that the slide release is very tight. I'll be picking mine up tomorrow and will go right to the range with it. Can't wait.

02-03-2010, 09:43 PM	#4
theotherTexasRich Joined: Jun 2008 Posts: 16	Bagger, I'd avoid using the slide stop to release the slide anyway. Over time it will wear out and it won't even hold the slide open. At that point, releasing the slide will no longer be a problem. I prefer to release the slide myself, so I'm fine with the way the SR9 works.

02-04-2010, 05:53 AM	#5
Bagger Joined: Oct 2008 From: Southern New England Posts: 90	Thanx for the responses. I have not read the manual as I figured it was much like the 'original SR9', but I will certainly read it. However, I have stripped the gun, cleaned it and oiled it ... but, I have not fired it. I'm not sure why the 'slide stop lever' is soooooooo tight. I'm not a weak guy, I'm over 215 pounds and work out regularly. So, strength is not a problem. But, displacing the stop lever and pulling back on the slide takes considerable effort on my gun. My associate at work could not do it, nor could my girl friend. BTW, this would not be good in a gun fight. Dropping the spent magazine, popping in a loaded mag and then wrestling with the slide stop lever to release the slide. I'm not sure I like this design. I'm used to tossing in a fresh mag, dropping the slide stop lever and bang, bang. It takes less than 2 seconds with my M&P 9. I do hope this improves.

02-04-2010, 09:32 AM	#7
wrv Joined: Oct 2009 Posts: 61	an interesting article about the debate can be found here: http://www.officer.com/web/online/On-the-Street/The-Great-Slide-Release-Debate/21$36789 in my area, it is pretty common among LEO's to be trained with the slingshot method.

02-08-2010, 08:37 PM	#8
A4Guy Joined: Feb 2010 From: WV Posts: 8	Mine is also very stiff. I don't mind it though. I just use the slingshot method. It only takes a tiny little tug back on the slide and the Slide Stop disengages. I don't have to pull back and then thumb the lever or anyhting. Just a tiny tug and let it go.

02-09-2010, 06:47 AM	#10
Bagger Joined: Oct 2008 From: Southern New England Posts: 90	TexasRich .... I fully understand and appreciate what you write. My training is different than what you describe. I have also dropped a magazine with a round or so still on board and rammed in a fresh mag while continuing to fire, too. However, most of these guns hold more than the SR9s 10 rounds and I feel more comfortable doing so. From what I can see on other message boards and this one, the SR9c is designed to have the slide stop lever used for just that purpose and not a slide release lever. I don't know why, but that seems to be the facts. I have 3 other Ruger pistols that seem to have the slide release lever work as such ... and not as a slide stop lever. This is what I am used to using. I'm going to sell the SR9c. It's a fine gun, but I can't live with the slide stop lever working the way it does.

02-09-2010, 07:24 AM	#11
A4Guy Joined: Feb 2010 From: WV Posts: 8	How much you want for your SR9c, Bagger?

02-09-2010, 07:33 AM	#12
Bagger Joined: Oct 2008 From: Southern New England Posts: 90	I was going to post this on the classified section .... which I prolly will anyway. Here's the deal: SR9c for sale in Connecticut. Purchased1/30/10 new. Gun is black (not SS slide). I have only run 250 rounds of 115 grn ammo from the LGS's indoor range a couple days ago. That is it. Gun is in perfect condition as from the Ruger factory. All materials included from Ruger are in the box. Gun is cleaned, oiled and in original condition packaging. I have photos if you are interested in seeing the gun. Price: $300 plus over night shipping costs to a FFL only. This could be over $60 from what I can see. Gun can not be shipped to CA, HI, MA, NJ, or NY because of extended magazine capacity. But, you already know this.

02-13-2010, 04:42 PM	#14
areyna Joined: Feb 2009 From: Houston Posts: 23	jman - silly question, but have you cleaned all the factory lube out of it yet? My slide was tight as hell till i cleaned it. 150 rounds later and the slide and slide lock/release action is very similar to my SR9 (2k+ rounds).