f> Recommendations for Blackhawk Cylinder Fit? - Ruger Forum

Ruger Forum

Recommendations for Blackhawk Cylinder Fit?

This is a discussion on Recommendations for Blackhawk Cylinder Fit? within the Gunsmithing forums, part of the Firearm Forum category; I've had my stainless .357 New Model Blackhawk since '77 and have never had any issue with it. I always wanted a companion stainless 9mm ...


Go Back   Ruger Forum > Firearm Forum > Gunsmithing

Reply
 
LinkBack Thread Tools Display Modes

Old January 10th, 2017, 07:21 AM   #1
 
MG34Dan's Avatar
 
Join Date: Mar 2014
Location: Austin, TX
Posts: 23
MG34Dan is on a distinguished road
Recommendations for Blackhawk Cylinder Fit?

I've had my stainless .357 New Model Blackhawk since '77 and have never had any issue with it. I always wanted a companion stainless 9mm cylinder for it but have never been able to find one. So, I picked up a nice condition blued 9mm cylinder in consolation. It needs to be fitted to my revolver. Does anyone have any recommendations for who to use for this service? I would prefer someone close to home, Austin Texas.



MG34Dan is offline  
Advertisements
Old January 10th, 2017, 12:24 PM   #2
 
Join Date: Jun 2011
Location: wayne nj
Posts: 23,585
bwinters is a name known to allbwinters is a name known to allbwinters is a name known to allbwinters is a name known to allbwinters is a name known to allbwinters is a name known to all
10 ring precision does good work. I do not know what their wait times are.
bwinters is offline  
Old January 16th, 2017, 01:05 PM   #3
 
Join Date: Aug 2012
Location: California
Posts: 1,907
Hondo44 will become famous soon enoughHondo44 will become famous soon enough
The only issue is the overall length. Never had one where the timing wasn't right on and I've converted a lot of guns with added cyls.

Will if fit in your frame? If not just dress down the gas ring in the front until it does. If too short, here's two in Texas:


Alan Harton (Colt SAAs also)
713-772-8314 or 713-907-6031
aharton@hotmail.com
Sharpstown, Texas, West S/W of Houston
Makes a .327 Fed Mag Bearcat; Custom Ruger New Bearcat from Single Action Service Chambered for the 327 Federal Magnum Cartridge

Long Hunter
Amarillo, TX
COWBOY ACTION FIREARMS - LONG HUNTER SHOOTING SUPPLY
Sounds like a nice package for $135.
Taper cylinder and ejector rod housing $45.00 USD
COWBOY ACTION FIREARMS - LONG HUNTER SHOOTING SUPPLY
Hondo44 is offline  
Reply

  Ruger Forum > Firearm Forum > Gunsmithing

Thread Tools
Display Modes


Similar Ruger Forum Discussions
Thread Thread Starter Forum Replies Last Post
Cost to fit cylinder badhatharry Ruger Single Action 9 July 4th, 2016 01:32 AM
Will These Grips Fit My NM Blackhawk? JBnTx Ruger Single Action 18 April 3rd, 2014 03:03 PM
Will a 9mm BlackHawk cylinder fit in a Glocking26 Ruger Single Action 3 April 25th, 2013 03:26 AM
Super Blackhawk Scope recommendations Guesswho Ruger Single Action 1 January 6th, 2012 10:28 PM
Brass rod to check barrel to cylinder fit bentrod Ruger Double Action 1 June 9th, 2009 07:02 PM

Top Gun Sites Top Sites List
Powered by vBulletin 3.8.7
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.1
Copyright © 2006 - 2017 Ruger Forum. All rights reserved.
Ruger Forum is a Ruger Firearms enthusiast's forum, but it is in no way affiliated with, nor does it represent Sturm Ruger & Company Inc. of Southport, CT.